2012 Ford Fusion Brakes Problems

The contact owns a 2012 Ford Fusion. The contact stated that his wife was involved in a crash noting that while stopped at a traffic light upon traffic beginning to move forward, the contacts wife took her foot off of the brake pedal slightly however the vehicle continued to lurch forward and in the process bumped into the vehicle in front of her with the entire front end of their vehicle. No property damage was reported. The vehicles came to a stop upon impact. The vehicle was towed to a local dealer. No warning lights were illuminated however the following message was displayed on the instrument panel that read "Brake Failure". A Police report was not filed. The vehicle was not destroyed. No injuries were reported. The vehicle was diagnosed and the contact was advised that the Anti Lock Braking System Module was faulty and would need to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 134,021.

The contact owns a 2012 Ford Fusion. The contact stated while driving at approximately 40 MPH, the brake pedal was depressed; however, the brakes failed to engage. The contact stated that the parking brake was used to slow and stop the vehicle. No warning light was illuminated. The vehicle was taken to an independent mechanic where it was diagnosed and determined that the brake master cylinder needed to be replaced. The vehicle was repaired; however, the failure persisted. The manufacturer was notified of the failure. The failure mileage was 137,221.

When coming to a stop the brake pedal went straight to the floor. No warnings were lamps were present. A mechanic checked the brake lines, master cylinder, and calipers and was not able to reproduce the issue. The mechanic deduced that the likely culprit was a faulty ABS control module. Had I been on the interstate or even had another vehicle infront of me, this would have been absolutely disastrous. This seems related to the recall for the older model fusions. This needs to be looked at.

The contact owns a 2012 Ford Fusion. The contact stated that while driving at an undisclosed speed and attempting to slow the vehicle, the brake pedal briefly became squishy. The contact stated that the brake pedal was depressed to the floorboard and required increased effort to bring the vehicle to a complete stop. There was no warning light illuminated. The vehicle was towed to the dealer, who diagnosed failures with the hydraulic control unit and anti-lock braking system. The vehicle was not repaired. The manufacturer was notified of the failure but provided no assistance. The failure mileage was approximately 180,000.

The abs control module failed at 59,000 miles. It's difficult driving on wet rainy roads with no ABS System, it's a Hughe safety risk especially on wet roads. The month of August was really rainy and it was extremely stressful driving. I have been looking for a repair but several auto repair shops including FORD can't get the part.

I noticed a couple of months ago my brakes where acting weird one minute they were fine and then sometimes the pedal would go to the floor and one day I was behind someone who had stopped suddenly and I hit my brakes fast and they went to the floor, for me not to hit the person in front of me I had to run off the road I was doing 30 mph and nobody was hurt but if I didn't have the options to run off the side of the road I would have rear-ended the other car and would have put me and the other people in a dangerous situation now my brakes go to the floor all the time I had it checked and every time I hit the brakes while in park they hear air coming from the ABS module which needs to be replaced is what I was told there was never no warning light that came on and never have come on before, this incident would have been much more dangerous if I was on interstate doing 70 + and I could have not stopped I've learned that the same problem has a recall on the 2006 - 2010 Ford fusion and all the reviews I've read the same problem is happening for the 2012 Ford fusion also so why hasn't it been put on the recall list because this puts people's life's in danger and it is a very hazardous safety issue

The contact owns a 2012 Ford Fusion. The contact stated while driving at various speeds and depressing the brake pedal, the brake pedal felt spongy and required to be pushed down to the floorboard to stop the vehicle. The contact stated that the vehicle hesitated while responding, extending the braking distance. There was no warning light illuminated. The contact state that the failure occurred intermittently. The vehicle was taken to the dealer several times, but the failure could not be replicated. The contact stated that the failure had been recurring more increasingly. The vehicle was taken back to the dealer, where it was diagnosed and determined that the HCU had failed and needed to be replaced. The vehicle was not repaired. The contact related the failure to an unknown recall. The manufacturer was notified of the failure and a case was opened. The manufacturer referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 130,000.

After I went over a set of railroad tracks, my brake pedal went to the floor while driving. I was able to stop but it scared me so bad because I almost wrecked! After stopping, I pumped brake pedal a few times and then it worked fine. I have newer pads, rotors, and calipers. Brake fluid was still full, and no leaking. Master cylinder is good. No idea what the problem is but I have seen online that this happens to a lot of 2012 Ford Fusions.

I started slowing down because a car in front of me was turning left. My brake pedal went to floor with no pressure whatsoever. Thankfully the car turned before I hit them. I lived 2 blocks away and was able to coast into my drive. Brake pads are good, master cylinder is good, calipers good, and no fluid leaking. There has to be a recall for this because it is very dangerous!!!

Intermittent loss of brakes, with pedal going to the floor. Couldn't stop when a deer ran out in front of me!! Entire brake system looks good. Is there a recall??

While my Student Driver 15 year old son was practicing for his driving test, the Brakes went out. The dash was lit up like a Christmas Tree, and when the Brake pedal was depressed, it touched the floor. The car did slow down briefly, then there was no friction what so ever from the brakes. My son, and wife could have ended up in a horrible accident, as the only way to stop the car was by allowing the car to roll to a complete stop. This is actually a know issue for Ford Fusions from 2006-2010. I brought this car to a dealership, and they diagnosed it as the ABS ABS Hydraulic Control Unit. They have already completed the repairs. One of the comments that was made is that if it had been a 2006-2010, it would have been replaced under recall. After the Brakes went out the Service Advance Trac light, and Check Brake system shown on my Dash Light. This is a very dangerous issues especially since I live in a heavily populated college town. My family, and/or another innocent bystander could have been extremely injured or even killed. I feel like Ford knows about this problem, and should be responsible to replace it.

My braking has not been correct. The brake pedal goes, almost to the floor, unless I pump the pedal. It has put me in scary situations when I have to hit the pedal hard. When I hit the pedal hard, it starts to stop, then goes down to the floor. The pedal is very spongy most of the time, with little reaction when you put your foot on it. At a higher rate of speed, you cannot slow down fast. Advise me my next course of action please

The contact owns a 2012 Ford Fusion. The contact stated while driving approximately 10 MPH in a parking lot, the vehicle went over a traffic speed bump, the brake pedal was depressed she felt soft. The brake pedal had to be depressed to the floorboard to stop the vehicle. The contact stated no warning light was illuminated. The contact stated that the brake failure had become constant. The contact had taken the vehicle to a local dealer, where it was diagnosed and determined that the brake booster assembly, master cylinder, and vehicle suspension arms in the front wheels needed to be replaced. The vehicle was repaired. The contact stated that the brake failure recurred. The manufacturer had been informed of the failure. The contact researched online and related the failure to NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic). The failure mileage was approximately 72,000. The contact stated that repairs have been made but something is still wrong with the vehicle.

Brake system failed while driving. Brake pedal went to the floor and lost all brake assistance. After diagnostics, it was determined to be the ABS control module and hydraulic module. This same model was subject to a recall that ended in 2010 MY however the same issues are persisting into the 2012 MY.

Brake pedal intermittantly sinks to floor; vehicle will stop but braking distance is substantially increased. No brake warning light comes on. Vehicle brought to dealer in November 2022 but dealer could not reproduce issue. Problem re-occured in January 2023; vehicle was towed to dealer. Again, dealer could not reproduce issue because it is very intermittant. At my insistance, and as a customer-pay repair, dealer replaced ABS HCU (hydraulic control unit) and ABS electronic control module. Note that there is a recall on older Fusion models for HCU failure but not 2012 model.

Reporting this issue after the fact as it closely resembles the events associated with earlier Ford Fusions documented under NHTSA Safety Campaign Number: 19V904000. After ABS was activated, the brake pedal felt extremely soft and the required braking distance greatly increased. This was initially fixed by replacing the master cylinder and flushing the braking system; however, that fix proved to be temporary. Soft brakes and large braking distance is now an intermittent issue. This car is available for inspection if needed.

Slippery/snowy conditions, applied brakes approaching a stop sign. ABS kicked in and brake pedal dropped to the floor. With reduced braking ability. This has continued since. This has happened the past 2 winters and will eventually just release and the brakes function normally, until the ABS is needed and then the same thing happens.

The contact owns a 2012 Ford Fusion. The contact stated while driving approximately 35 MPH, he drove over a bump on a train track and had to depress the brake pedal down to the floorboard for the vehicle to come to a complete stop. No warning light was illuminated. A local dealer was made aware of the failure and informed the contact that the dealer did not service vehicles 10 years or older. The vehicle was then taken to an independent mechanic to be diagnosed. The contact was informed that the ABS control module needed to be replaced. The contact linked the failure to NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic) however, the VIN was not included in the recall. The vehicle was not repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 95,000.

There is intermittent failure when brakes are applied. Periodically when we push the brakes they go all the way to the floor and the car keeps moving forward and not brake. I have researched this and it seems Ford has recalled some of the ABS components in this model of car but not for this year/VIN.

Shortly after a having the rear brake pads replaced, I noticed that the handbrake (or e-brake) would lose tension over night, but not always. Since this was occasional, then it appeared to be a hydraulic issue. About three months later (9/15/22), the brake pedal stopped working correctly and the pedal had to travel further, and be pushed to the floor to bring the car to a gradual stop. I almost went into the back of another vehicle, it's fortunate that I was travelling at a low speed when the brake failed. I took the vehicle to my Ford dealer/service shop and, following their inspection and diagnostic assessment, was told that there is a problem with the hydraulic control unit (HCU), and that the it would need to be replaced and the lines flushed. My vehicle is a 2012 Fusion. This sounds like the same HCU problem that lead to the recall for 2006-2010 Ford Fusion vehicles - refer Ford Motor Company (Ford) Recall No. 19S54 - https://static.nhtsa.gov/odi/rcl/2019/RMISC-19V904-0442.pdf Per linked pdf, the NHTSA opened EA18-002 and included inquiry of 2006-2012 Fords Fusion vehicles. It appears that only the older 2006-2010 models were included in the recall. However, as the newer (2012) models reach a similar mileage or age, it may worth reevaluating and extending the scope of the recall in the interest of safety for the traveling public. Had the brake failed while traveling a higher speed, then my life, my children's lives and others would have been at risk.

The contact owns a 2012 Ford Fusion. The contact stated while driving approximately 30 MPH, the brake pedal was depressed but the vehicle failed to stop before the pedal went to the floorboard. The contact stated no warning light was illuminated. The contact took the vehicle to an independent mechanic who determined that the brake pads needed to be replaced. Additionally, the hydraulic system was bled. The contact stated that the failure reoccurred and the vehicle was driven to a dealer where it was diagnosed and determined that the hydraulic control unit (HCU) needed to be replaced. The contact was advised that the parts were on backorder. The contact was advised that the failure was related to NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic) however, the VIN was not included. The vehicle was not repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 165,000.

Approximately three months ago the ABS system engaged due to applying my brake to avoid pedestrian crossing in front of me. After continuing to drive the brake pedal was very soft and traveled nearly to the floor of the car. The next day the system returned to normal. Several days ago, on 6/25/2022 this occurred once more when a hard brake was needed to avoid a suddenly stopped vehicle and the same problem became present with a soft petal and having to pump the pedal, my wife was the operator this time. The vehicle has not yet been inspected by any entity. I have inquired about this problem from my mechanic and also have researched the problem and see there is a recall > 19S54 also an update to the recall > EA18-002 that states my 2012 Fusion is included in the recall and will now contact the local Ford Dealership to have this concern corrected. In my research I see that is due to the ABS module sticking due to corrosion from the wrong brake fluid. I have had several close calls while operating my car, the recall states Ford advises it is safe to drive. This I strongly disagree with, particularly since my wife uses this vehicle and is not as skillful as I when it comes to mechanical issues such as this. There were no warning lights, or messages, the issue has now cleared up again and brakes are operating normally as before this incident. This vehicle is readily available for inspection on request.

The contact owns a 2012 Ford Fusion. The contact stated while driving on the highway at an undisclosed speed and depressing the brake pedal, the pedal went to the floorboard. There were no warning lights illuminated. The contact was able to pull off the highway and the vehicle rolled to a stop. The vehicle was not taken to a dealer or independent mechanic to be diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 120,000.

The contact owns a 2012 Ford Fusion. The contact stated while driving 20 MPH and depressing the brake pedal, the vehicle failed to stop within a reasonable time. The contact stated no warning light was illuminated. The contact stated he was able to stop the vehicle after pumping the brake pedal. The contact took the vehicle to the local dealer however, the mechanic was unable to duplicate the failure. The contact continued to experience the failure. The contact took the vehicle back to the local dealer, where it was diagnosed and the brake lines were flushed several times. The vehicle continued to experience the failure. The contact took the vehicle back for the third time and was informed that the rear and front brake calipers, the ABS hydraulic control unit (HCU), and the brake master cylinder needed to be replaced. The vehicle was not repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 95,000.

After Replacing some Calipers, Rotors & Pads I took My vehicle to Meineke Car Care Center in Lawrence, Indiana to have the Brake system Flushed ("Bled") I got my car back and immediately after pulling off I had NO PEDAL! ALMOST GOING THROUGH A FENCE! My Hand Brake saving me intime. I declined to have it reserviced at Meineke and had it looked at by a Local Mechanic I trust. He informed me After Bleeding the Master Cylinder, ABS Module with a Scan Tool and All Calipers that there was still no pedal. Which meant one thing The HCU on the ABS Module is Bad. Which was likely because 2006-2010 Models of the Ford Fusion have a Recall on the ABS/HCU for Loss of Brakes. WHY THE 2012 MODELS DO NOT HAVE A RECALL ASWELL IS BEYOND ME? Even though the 2012 Model Shares ALOT of Key components with the previous year's models. Including the ABS/HCU. Why is the 2012 not included? Obviously Corporations, Federal Regulators & Insurance companys in Kahoots to dampen the blow back to the Automotive industry AT THE EXPENSE OF PEOPLES LIVES!!! DO THE RIGHT THING

After starting the car, the brakes were not working properly--it required a lot of pressure to get the brake pedal to work. The brake light also came on indicating a problem with the ABS. After turning the car off and restarting it, the brakes worked fine again. The same thing happened the next day. That's when we took it for repairs. Our mechanic advised us to take it to a Ford dealer. Santa Monica Ford told us the ABS module and HCU need to be replaced at a cost of $2800 (and because there are delays getting the parts from Ford, it will take at least a couple of weeks). There is a related recall on Ford Fusions up to 2010, NHTSA campaign number: 19v904000 (service brakes, hydraulic). After some research, it's apparent that this is a common problem for Ford Fusion 2011 and 2012 models as well. It looks like the problem extends through 2012 and the recall should apply to those model years as well.

I have a 2012 Ford Fusion and my breaks went out I replaced the master Cylinder in it as well as the brake booster and still didn’t have any brakes. While driving I couldn’t stop my Car had to go off to a ditch thankful that I didn’t have a accident I’ve been told that the ABS module might be the problem this should be a recall on this problem.

On 08/07/2021 at approximately 3 pm while driving the vehicle low brake fluid level light indicated on dashboard. Stopped at a gas station and checked to make sure there was no brake fluid leaking and checked brake fluid level which was low. The cars brakes were still operating properly and we returned to the location we were staying to find an auto parts store to purchase brake fluid. At 6 pm, drove to the auto parts store to get brake fluid. We purchased the appropriate fluid and topped of the brake fluid reservoir. The low brake fluid light turned off on the dash after topping off the brake fluid. About 2 ounces were added. Upon leaving the auto parts store, we pulled out onto the road and when trying to brake, the brakes malfunctioned, the pedal went completely to the floor and the car did not stop normally and hit another vehicle. Police report attached. No injuries and minor damage to both vehicles bumpers Car was pulled off the road and was towed to shop for inspection as the brakes would not stop the car. Shop #1 replaced the master cylinder and the brakes still did not operate properly. Car was towed to shop #2 (Ford Dealer) and they diagnosed it as a failed ABS HCU unit in the vehicle that was not communicating with the onboard computer system. ABS HCU was replaced by the Ford Dealer and vehicle is now braking as normal. There were no warnings from the vehicle computer system that there were any issues with the brakes other than the low brake fluid level light, which was resolved by adding brake fluid. The 2006-2010 Ford Fusions have a recall for the ABS-HCU unit, but the recall did not include the 2011 and 2012 Ford Fusions, even though it appears to be the same ABS HCU unit. Upon doing research on the internet, this is a common problem with this year of Ford Fusion and there are no warnings or indications that this may occur. I feel the vehicle should be recalled and the brakes fixed.

A few weeks ago I went to slow to a stop at the end of my driveway at approximately 5mph. My brake pedal dropped to the floor and i had to repress on the brake pedal to come to a complete stop. It continued working properly for a week or so when it happened again. The same week I was backing out of another driveway slightly down hill and attempted to come to a complete stop to look for traffic. Luckily there was none because my stopping distance was around 12 ft or so going maybe 3mph with the brakes completely pressed. I have since had my brake pads changed and all other components checked and was told were working properly. Now my stopping distance at 10mph is at least 3-4ft. I am too afraid to drive my vehicle at higher speeds on any road due to the stopping distance issues.

While Driving my 2012 Ford Fusion like any other day… As approaching a 4-way intersection my traffic light was changing to red. When I went to stop using my brakes, my car would not stop at all and went completely through the intersection, and oncoming cars at each directions we’re coming towards me and my children. The brakes were as if they were not there and went completely to the floor and would not or did not stop my car at all. After several times pumping the brakes and strongly engaging in pulling the emergency brake numerous times I finally got my car to somewhat stop. This was the scariest thing I have ever experienced. Most definitely the most dangerous thing I have ever experienced my entire life for myself and my young children. We are truly lucky to be alive from these brakes completely, and unexpectedly spur of the moment going out! No warning!!! Models 2006-2010 Ford Fusions have a recall on this same exact brake system and have the same exact problem with the braking system unexpectedly and dangerously going out!!! Please get the recall extended on past 2010 and include 2011 and 2012 Ford Fusions!!! As they have the same exact braking systems!!!

1) Brake Hydraulic Control Unit (HCU) failure. Dealership removed and replaced HCU assembly and ABS module. All parts retained by Dealer. 2) HCU brake failure made stopping very difficult and slow to stop. Dealer recommended not driving until repaired. 3) Dealer confirmed HCU failure with computer code analysis. 4) HCU and effected parts not inspected by anyone other than Dealer. 4) numerous red ABS and brake warning lights upon backing out of garage to street. I shut the engine off and restart in the hope of correction, to no avail. Problem re-occurred. Vehicle could be stopped but with difficulty -- slow to stop and hard to stop. Dealer replaced HCU assembly and ABS module and added PM1C brake fluid (DOT3), This HCU failure apparently has been a problem in Ford Fusion and other Ford vehicles (see Safety Recall 19S54 -Anti-Lock Brake System Hydraulic Control Unit Valve Function -- 2006-2010 Ford & Lincoln Mercury). It doesn't look like the problem has been resolved. Note that brake fluid used is DOT 3 and not the NTSB recommended remedy DOT 4 brake fluid

UPON APPLYING BRAKE PRESSURE, THE PEDAL MUST TRAVEL A SIGNIFICANT DISTANCE BEFORE ANY BRAKING IS FELT. MY CAR HAS HAD NEW BRAKES PUT ON, WHERE THE MECHANIC HAS SAID THERE ARE NUMEROUS COMPLAINTS FROM OWNERS WITH THE SAME CAR. BRAKING DISTANCE IS SIGNIFICANT AND I AM ABLE TO FEEL THE FLOOR WITH MY FOOT. THIS SHOULD NOT BE THE CASE. FORD DOES NOT SEEM TO HAVE A SOLUTION, SO THEY CONTINUALLY PUSH IT UNDER THE RUG. I HAVE VERIFIED THAT MY MASTER CYLINDER IS WORKING AS EXPECTED WITH NO AIR IN MY LINES. I DO A LOT OF FREEWAY DRIVING, BUT IN ORDER TO STOP ON TIME, I HAVE TO GET OFF THE FREEWAY DOING 10 MPH LESS TO ENSURE I CAN BRAKE IN TIME.

THE BRAKES ARE "SPONGY". TOOK IT TO OUR MECHANIC WHO REPLACED THE MASTER CYLINDER TWICE AND THE BRAKES WERE STILL "SPONGY". HE LOOKED AT THE BRAKES AND THEY LOOKED GOOD. HE RECOMMENDED THAT THE ABS SENSOR BE REPLACED, BUT FORD WOULDN'T SELL IT TO HIM. SO, WE TOOK IT TO THE FORD DEALER AND THEY REPLACED THE BRAKES, CALIPERS, ETC. AND THE BRAKES REMAIN "SPONGY". THEY SAID THEY NEEDED TO REPLACE THE MASTER CYLINDER, BUT IT IS BRAND NEW.

WHEN IN MOTION, THE VEHICLE'S BRAKE PEDAL HAS EXCESSIVE TRAVEL, ALMOST NEEDING TO BE PUSHED TO THE FLOORBOARD BEFORE ANY BRAKING OCCURS. THE UNCERTAINTY OVER THE CAR'S BRAKING ABILITY MAKES IT DANGEROUS TO DRIVE. NO ERROR CODES OR ABS LIGHTS PRESENT. LOCAL REPAIR SHOP REPLACED BRAKE PADS AND ROTORS AND FOUND NO AIR IN THE SYSTEM WHEN THEY BLED THE BRAKES. THEY SPECULATED IT IS POSSIBLY THE HYDRAULIC CONTROL UNIT FOR THE ABS. THERE HAS BEEN A RECALL ON EARLIER FUSION MODELS FOR THIS ISSUE, BUT NOT 2012 MODELS FOR SOME REASON.

BRAKE PEDAL BECAME SOFT AND THE BRAKING DISTANCE WAS INCREASED AFTER ABS ACTIVATION ON SNOW/ICE. I TAPPED THE BRAKES TO CHECK HOW SLICK THE ROAD SURFACE WAS, THIS ACTIVATED THE ABS. I THEN TRAVELED 30 FEET AND APPLIED THE BRAKES TO MAKE A RIGHT HAND TURN, THE BRAKES WENT NEARLY TO THE FLOOR CAUSING ME TO TAKE THE TURN AT A HIGHER THAN SAFE SPEED.

ALL THSYMPTOMS THAT OCCUR AS DESCRIBED IN YOUR CAMPAIGN INVOLVING FORD RECALL NO. 19S54 AND SPECIFICALLY EA18-002. THE BRAKE PEDAL HAS EXCESSIVE TRAVEL BEFORE ENGAGING THE BRAKES. THIS SIGNIFICANTLY INCREASES BRAKING TIME. I HAVE HAD SEVERAL NEAR MISSES, ALMOST RESULTING IN ACCIDENTS.

THE REAR BRAKE CALIBERS HAVE SEIZED UP TWICE NOW. 1ST TIME WAS JUNE 2017, SERVICED BY FIRESTONE, AND JUST RECENTLY SEPT 12TH 2020. BOTH TIMES REQUIRED A FULL BRAKE REPAIR. FIRST HAPPENED AT 72,000 MILES AND NOW AT 142,000 MILES. BOTH CAUSE A LOSS OF BRAKING IN THE VEHICLE. IN JUNE OF 2017 THE VEHICLE WAS MOVING BETWEEN 30 TO 45 MPH WHEN IT SEIZED UP. WE DROVE IT TO NEAREST SHOP IN ILLINOIS SO WE CAN START OUR DRIVE BACK TO GEORGIA. SECOND TIME WAS NOT AS BAD AS I RECOGNIZED THE SYMPTOMS AND GOT IT IN FOR REPAIRS BEFORE FULL SEIZURE OF THE BRAKES. ONLINE REVIEW SHOWS MANY PROBLEMS WITH THE BRAKES ON THIS CAR MODEL.

BRAKE PEDAL DROPS ALMOST TO FLOOR AT TIMES GREATLY INCREASING STOPPING DISTANCE WHEN APPROACHING A STOP OR WHEN I SLOW DOWN. THIS NECESSITATES THE NEED TO PUMP THE BRAKE PEDAL AND IN EXTREME CIRCUMSTANCES NEEDING TO SWERVE TO AVOID A COLLISION . THIS PROBLEM OCCURS WITH NO WARNING AT ALL. THIS SEEMS TO BE A KNOWN ISSUE WITH THE FUSION.

CAR WAS IDLING IN LINE AT A DRIVE THRU FOR ABOUT 5 MINUTES. DRIVER RELEASED FLOOR BRAKE TO MOVE UP IN LINE. AFTER PULLING UP A FEW FEET, AND THEN TRYING TO SLOW THE CAR, THE BRAKE PEDAL TRAVELED ALL THE WAY TO THE FLOOR AND BRAKING DISTANCE WAS EXTENDED. DRIVER WAS AFRAID THE CAR WOULDN'T STOP. CAR HAS A NEW ELECTRONIC THROTTLE BODY AND HYDRAULIC ABS PUMP, BUT PROBLEM PERSISTS. DRIVER IS CONSIDERING GETTING A NEW CAR. *TR

ON TWO OCCASIONS THE BRAKE SYSTEMS FAILED TO WORK. 1. DRIVING ON RT 4 (DOUBLE LANE STATE RD.) IN MAINE SPEED APPROX 60 MPH. THERE WAS 4 TO 5 CARS AHEAD OF ME. SUDDENLY, EVERYONE APPLIED THEIR BRAKES. THE FIRST CAR IN LINE DECIDED TO TAKE A LEFT HAND TURN. I APPLIED MY BRAKES-BRAKE PEDAL WENT TO THE FLOOR--NO ANTILOCK BRAKES. HAD TO SWERVE INTO ONCOMING LANE. FINALLY CAR STOPPED. A SECOND TIME IT HAPPENED WAS ON A HILL IN DOVER, NH. THERE IS A TRAFFIC LIGHT AT BOTTOM OF HILL. AS I STARTED DOWN THE HILL, I APPLIED THE BRAKES AGAIN NO BRAKES NO ANTILOCK BRAKES. LUCKILY WAS ABLE TO STOP BY TIME I REACHED THE LIGHT. I TOOK CAR TO A LOCAL GARAGE THEY TEST DROVE AND IT OPERATED FINE. THEY REMOVED WHEELS AND LOOKED AT ALL THE BRAKES. THE REAR BRAKES, CALIPERS, PADS ETC WERE REPLACED A YEAR AGO. THE FRONT BRAKES LOOKED BRAND NEW EVEN THOUGH THERE WAS ALMOST 52,000 MILES ON THEM.PADS AND ROTORS LOOKED LIKE NEW, SHINY, NO SCRATCHES. COULD NOT FIND THE PROBLEM. WE DECIDED TO REPLACED THE ROTORS AND PADS WITH A SOFTER VERSION. SEEMS TO BE WORKING??? *TR

BRAKES FAILED STOPPING SUDDENLY AT 70 MPH NEARLY HITTING A ROW OF CARS AHEAD OF ME PEDAL WENT TO THE FLOOR INCREASING STOPPING DISTANCE PROBABLY 400 PERCENT WITH VERY WEAL BRAKES. BRAKE LIGHT AND ABS INOP LIGHT ILLUMINATED. WAS ABLE TO DRIVE CAR HOME SLOWLY USING HYBRID ELECTRIC MOTOR BRAKES. REPAIR SHOP SAID BRAKE CONTROL MODULE HAS FAILED THIS IS A LOW MILEAGE CAR UNACCEPTABLE COULD GET SOMEONE KILLED. *TR

THE BRAKE PEDAL IS SOFT AND TRAVELS FURTHER THAN NORMAL. BRAKING DISTANCE IS SIGNIFICANTLY INCREASED. I BROUGHT THE CAR TO THE DEALERSHIP AND TURNED OUT THAT THE HYDRAULIC CONTROL AND THE ELECTRONIC CONTROL UNITS ARE BOTH FAULTY, BASED ON SOME RESEARCH IT APPEARS THIS IS A KNOWN ISSUE. IT HAS A NEW MASTER CYLINDER AND BRAKES HAVE BEEN BLED PROFESSIONALLY. THIS DID NOT CURE THE PROBLEM. IT IS UNSAFE. I WANT THE DEALER TO DO SOMETHING ABOUT THIS AT NO COST TO ME. THIS IS A RECALL ITEM FOR 2010 FUSION, BUT NOT 2012.WHY??? I'VE SEEN SEVERAL COMPLAINTS ABOUT THIS SAME ISSUE WHY HASN'T ANYTHING BEEN DONE,SAFETY SHOULD BE TOP PRIORITY.

THE BRAKE PEDAL IS SOFT AND TRAVELS FURTHER THAN NORMAL. BRAKING DISTANCE IS SIGNIFICANTLY INCREASED. THIS BEGAN AFTER THE ABS SYSTEM ENGAGED SEVERAL WEEKS AGO AFTER NORMAL BRAKING OVER A ROUGH SECTION OF ROAD AND IT HAS NOT RETURNED TO NORMAL. ALL BRAKE PADS AND ROTORS WERE REPLACED AND THE SYSTEM WAS FLUSHED BUT THE PROBLEM REMAINS. BASED ON SOME RESEARCH IT APPEARS THIS IS A KNOWN ISSUE CAUSED BY A FAULTY ABS MODULE.

ON OCCASION WHEN THE BRAKES ARE PRESSED IT SIMPLY FALLS TO THE FLOOR AND HAS TO BE IMMEDIATELY REPRESSED. IT HAS A NEW MASTER CYLINDER AND BRAKES HAVE BEEN BLED PROFESSIONALLY. THIS DID NOT CURE THE PROBLEM. IT IS UNSAFE. I WANT THE DEALER TO DO SOMETHING ABOUT THIS, NO COST TO ME. OCURES WHILE IN MOTION.

WHILE TRAVELING AT A SLOW RATE OF SPEED THE BRAKES ON MY 2012 FORD FUSION HYBRID FAILED TO ENGAGE, WITH THE PEDAL TRAVELING ALL THE WAY TO THE FLOOR. THE CAR WAS TUNED OFF AND RESTARTED AND THE BRAKES SEEMED TO WORK AGAIN. I HAD THE VEHICLE TOWED TOT HE DEALERSHIP AND TURNED OUT THE THE HYDRAULIC CONTROL AND THE ELECTRONIC CONTROL UNITS ARE BOTH FAULTY. THIS IS A RECALL ITEM FOR 2010 FUSION HYBRIDS, BUT NOT MY YEAR.

MY SON WAS DRIVING & PREPARING TO STOP AT A STOP SIGN. IT WAS A ROAD HE WAS VERY FAMILIAR WITH. THE BRAKE PEDAL WENT TO THE FLOOR. HE ATTEMPTED TO SLOW THE VEHICLE & TURN THE CORNER BY SWERVING UP AN EMBANKMENT SLIGHTLY. HE REALIZED IT WOULDN'T SLOW. HE PUMPED THE BRAKES SEVERAL TIMES WITH NO BRAKE RESPONSE. HE CHOSE BETWEEN A GARAGE & A TREE TO STOP THE VEHICLE. HE HEADED FOR THE TREE. IN INSURANCE INVESTIGATION, BRAKES FUNCTIONED NORMALLY. SEVERE UNDERCARRIAGE DAMAGE HAD BEEN REPAIRED LESS THAN 2 WEEKS PRIOR TO THE ACCIDENT. POLICE WERE CALLED TO ACCIDENT SCENE & FILED REPORT. THERE WERE NO SKID MARKS AT THE SCENE. THE SPEED WAS ESTIMATED AT 35-40 MPH - WITHIN/LOWER THAN SPEED LIMIT. *LN *DL CONSUMER STATES THAT THE VEHICLE WAS TOTALED IN THE ACCIDENT. INSURANCE COMPANY IS MOVING VEHICLE TO A SALVAGE POOL. THEY CONDUCTED AN INVESTIGATION AND LOOKED AT THE ABS/HCU AND DETERMINED THAT THE BRAKES DID NOT CAUSE FAILURE. *DL

THIS REFERENCES TRACKING NO. 11246006. FOR THE SECOND TIME, NOV. 29, 2019, MY BRAKES FAILED. FORD FUSION 2012, 40,100 MILES. I WAS PARKED IN A GARAGE - STARTED CAR, PUT IN DRIVE AND ALL FAILURE LIGHTS CAME ON AND NO BRAKES WHEN I USED THE BRAKE PEDAL. MY INVOICE FOR $3,200 TO REPAIR STATED "INSPECTED AND FOUND THAT ECU AND HCU BOTH HAVE INTERNAL FAILURE NOT ALLOWING COMPUTERS TO CONTROL RESPECTIVE COMPONENTS. ... PER PIN POINT TEST." I BELIEVE THIS FAILURE IS A RESULT OF DEFECTIVE PARTS ON THE FORD VEHICLE. THIS CAR HAS ONLY 40,000 MILES -- IT SHOULD NOT HAVE A FAILURE OF THIS MAGNITUDE. I BELIEVE I SHOULD BE REFUNDED THE AMOUNT I HAD TO PAY FOR REPAIR. P.S. AFTER PAYING $3,200 FOR THE REPAIR, I WAS PRESENTED WITH A CAR THAT HAD SO MANY LEAVES ALL OVER THE CAR, I HAD TO USE MY SNOW REMOVAL WAND TO REMOVE THE LEAVES BEFORE I COULD SEE OUT THE WINDOWS -- THIS IS NOT ACCEPTABLE. THEY HAD MY CAR FOR 12 DAYS TO REPAIR??

IF I HIT A LARGE BUMP OR GOING DOWN A ROUGH ROAD IF YOU GO TO HIT THE BRAKES IT'S LIKE THEY AREN'T THERE AND THE BRAKE PEDEL GOES ALL THE WAY TO THE FLOOR WITH A LITTLE BRAKE AT THE FLOOR , YOU HAVE TO STOP AND TURN THE CAR OFF AND PUMP THE BRAKES A FEW TIMES AND THEN THEY ARE OK , IT ALSO HAPPENS WHEN THE ABS WORKS , I THINK THE PROBLEM IS IN THE ABS VALVE ASSEMBLEY THEY RECALLED THE 2008 TO 2011'S FOR THIS PROBLEM BUT NOT THE 2012'S

ON SEPTEMBER 26, 2014, I WAS INVOLVED IN AN ACCIDENT AS WE WERE DRIVING ON A CITY STREET TO WHERE MY PASSENGER SEAT BELT DID NOT WORK UPON FRONTAL HEAD ON IMPACT OR MY AIRBAGS DIDNT GO OFF CAUSING ME TO COLLIDE INTO THE DASH BOARD. THIS CAUSED LIGAMENT TEARING IN MY RIGHT HAND/SHOULDER AS THAT WAS THE INITIAL IMPACT. NOW I HAVE TO CONTINUE TO SUFFER FROM LIMITATIONS ON THE USE OF MY RIGHT HAND/SHOULDER COMPLICATIONS. FOR THE BRAKE ISSUE BEGINNING DECEMBER 1, 2019. IT HAS COME UP THAT THE EMERGENCY BRAKE IS STICKING AND TEARING THROUGH MY BRAKES AS I AM DRIVING ON THE STREET OR EVEN HIGHWAY CAUSING IT TO SMOKE AROUND MY BACK TIRES. I NEARLY LOST MY LIFE ONCE, AND DO NOT WANT IT TO HAPPEN AGAIN, BUT WHEN CHECKING BRAKE RECALLS IT'S ONLY UP TO A 2010 MODEL AND I HAVE A 2012 MODEL. THIS ISSUE HAS CAUSED THE PADDING ON MY BREAKS TO COMPLETELY DISAPPEAR LEAVING ME UNABLE TO COME TO A STOP.

TL* THE CONTACT OWNS A 2012 FORD FUSION. WHEN THE VEHICLE WAS TAKEN TO HAVE THE OIL CHANGED, THE MECHANIC HEARD A WINDING SOUND COMING FROM THE TRANSMISSION. WHILE ATTEMPTING TO ACCELERATE, THE VEHICLE HESITATED AND EXHIBITED A JERKING SENSATION BEFORE ACCELERATING. WESTFIELD FORD (LOCATED AT 6200 S LA GRANGE RD, COUNTRYSIDE, IL 60525, 708-354-8600) HEARD THE WINDING NOISE UNDER THE HOOD AND DIAGNOSED THAT THERE WAS A DEFAULT WITH THE PARKING BRAKE AND ROTORS. THE VEHICLE WAS REPAIRED, BUT THE FAILURE CONTINUED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND INFORMED THE CONTACT THAT IT WOULD NOT BE COVERED UNDER WARRANTY BECAUSE IT WAS EXPIRED. THE MANUFACTURER PROVIDED CASE NUMBER: CAS25108633. THE APPROXIMATE FAILURE MILEAGE WAS 50,000.

ABS WARNING LIGHT AND LOW BRAKE FLUID LIGHT ON. THE LINES AND MASTER CYLINDER WERE REPLACED AND THE BRAKES ARE IN WORSE CONDITION. LOOSE AND POOR RESPONSE WHEN MOVING AND NEEDING TO STOP.

TL* THE CONTACT OWNS A 2012 FORD FUSION. WHILE DRIVING APPROXIMATELY 25 MPH, A GRINDING NOISE EMERGED FROM THE REAR PASSENGER SIDE OF THE VEHICLE. IN ADDITION, THE ABS, TRACTION CONTROL, SERVICE ADVANCETRAC, AND TIRE PRESSURE SENSOR ILLUMINATED. THE VEHICLE WAS NOT TAKEN TO A DEALER OR AN INDEPENDENT MECHANIC FOR DIAGNOSTIC TESTING. THE CALIPERS AND BRAKE PADS WERE REPLACED BY THE CONTACT. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 180,000.

BRAKES ON 2012 FORD FUSION HYBRID COMPLETELY FAILED WHILE DRIVING ON 8/30/19. MY SON WAS DRIVING AND WAS GOING 30 MPH. HE USED THE PARKING BRAKE TO STOP THE CAR. I HAD THE CAR TOWED TO THE FORD DEALER SERVICE DEPARTMENT 9/3/19. I AM TOLD THE 'ABS MODULE' FAILED. COST FOR PART IS $700. TOTAL REPAIR COST $1400.

WHILE EXITING FROM MY CONDO PARKING GARAGE, WHEN APPLYING THE BRAKE, BRAKE LIGHTS CAME ON AND THERE WAS BRAKE FAILURE.

AFTER MY ABS SYSTEM ENGAGED WHILE DRIVING DOWN AN UNEVEN ROAD, MY BRAKES HAVE BEEN SOFT FOR ABOUT A WEEK NOW. I'VE TRIED TO PUMP THEM BUT IT DOESN'T SEEM TO DO ANYTHING AND I NEED EXTRA DISTANCE TO BRAKE THAN I NORMALLY WOULD. ALSO, WHEN THE ABS SYSTEM ENGAGED THE BRAKE PEDAL WENT STRAIGHT TO THE FLOOR. THIS HAS HAPPENED BEFORE WHEN I WAS DRIVING THROUGH SNOWY CONDITIONS THIS PAST DECEMBER. THE ABS ENGAGED AND THEN THE BRAKES WERE SOFT FOR A WEEK. IT FINALLY JUST SOMEHOW FIXED ITSELF.

BRAKES BEGAN TO FEEL SPONGY. I HAD A SMALL ACCIDENT WHEN I COULD NOT BRAKE CAUSING DAMAGE TO ANOTHER'S CAR. REPLACED THE BRAKE PADS, HAD THE SYSTEM BLED BUT NOW I HAVE NO BRAKES. I HAVE NO BRAKE PEDAL AT ALL. REPLACED THE MASTER CYLINDER, FRONT CALIPE, BRAKE BOOSTER, AND BRAKE STILL HAVE NO BRAKE PRESSURE AT ALLL.

WHILE IN MOTION ON A CITY STREET, THE ABS LIGHT, THE RED BRAKE LIGHT, AND THE TRACTION CONTROL LIGHT ILLUMINATED ON THE INSTRUMENT PANEL. BRAKE PEDAL ENGAGEMENT REQUIRES MORE TRAVEL TO ENGAGE THE BRAKES. THE VEHICLE WAS TAKEN TO A LINCOLN DEALERSHIP FOR REPAIR. THE DEALER NOTED THAT THE ABS MODULE FAILED. AFTER A CLOSE INSPECTION, IT WAS DETERMINED THAT THE ABS MODULE HAD FAILED DUE TO BRAKE FLUID CONTAMINATION. THE ABS MODULE WAS REPLACED, BUT I'M CONCERNED MORE WITH THE APPARENT CAUSE, WHICH APPEARS TO BE THE DEGRADATION OF THE ABS HYDRAULIC CONTROL UNIT (HCU), WHERE THE ABS MODULE ATTACHES TO. THE ABS MODULE SHOULD HAVE ZERO FLUID CONTAMINATION. IT WOULD SEEM THAT THE REPLACEMENT ABS MODULE WILL FAIL FROM THE FLUID INGRESS CONTAMINATION AGAIN. PLEASE REVIEW ATTACHED PHOTOS AND RECEIPT. THANK YOU.

THE EMERGENCY CABLE ON THE LEFT SIDE I HUNG UP CAUSING THE BRAKE TO WEAR OUT PREMATURELY

BRAKE PEDAL WILL GO ALL THE WAY TO THE FLOOR AND NOT STOP THE CAR. AT TIMES THE ABS WILL APPEAR TO ACTIVATE. THIS COULD BE ON DRY PAVEMENT OR ICE ROAD SURFACE. HAS BEEN IN THE SERVICE SHOP SEVERAL TIMES AND STILL NO SOLUTION. THIS CAR HAS UNDER 60K MILES.

WHILE DRIVING AWAY FROM MY CURBSIDE PARKING SPOT TO GO TO WORK, THE DASHBOARD LIGHTS STARTED FLASHING AND SAID SOMETHING ALONG THE LINES OF "BREAK SYSTEM FAILURE" OR "CHECK BREAK SYSTEMS", AND I WAS UNABLE TO BRAKE AT ALL. I MANAGED TO CHANGE COURSE AND PULL OVER AND LET THE CAR STOP ON ITS OWN. ONCE STOPPED, I TURNED THE CAR OFF AND THEN BACK ON AGAIN. I TRIED TO SLOWLY MOVE AND THEN BRAKE, AT WHICH TIME THE BRAKES WERE SUCCESSFUL AND STOPPED THE CAR. I DROVE THE SHORT DISTANCE BACK TO MY HOUSE AND TOOK AN ALTERNATE VEHICLE. THIS IS INCREDIBLY CONCERNING CONSIDERING I CARRY MY WIFE AND THREE CHILDREN IN IT AND WE FREQUENTLY TAKE LONG ROAD TRIPS TO SEE FAMILY. HAD THIS HAPPENED ON ONE OF THOSE TRIPS, ESPECIALLY WHILE DRIVING LONG DISTANCES ON FREEWAYS THAT TEND TO BOTTLENECK, THE RESULTS COULD HAVE BEEN DEVASTATING, NOT JUST FOR US BUT ALSO OTHERS.

TL* THE CONTACT OWNS A 2012 FORD FUSION. WHILE ATTEMPTING TO STOP THE VEHICLE, THE BRAKE PEDAL TRAVELED TO THE FLOORBOARD AND THE BRAKING DISTANCE WAS EXTENDED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO REPLACED THE BRAKE PADS, ROTORS, AND CALIPERS, BUT THE FAILURE CONTINUED. THE MECHANIC DIAGNOSED THAT THE ANTI-LOCK BRAKING SYSTEM WAS FAULTY AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE LOCAL DEALER AND MANUFACTURER WERE NOT NOTIFIED. THE FAILURE MILEAGE WAS 94,000. *BF. *TR

AT 80,000, MY BRAKES FAILED. IT STARTED WHEN I STARTED THE CAR IN THE MORNING AFTER IT SAT IN THE GARAGE OVERNIGHT. WHEN I STARTED THE CAR, I PUT MY FOOT ON THE BRAKE AND THEN PUT HE CAR IN REVERSE. MY FOOT WENT TO THE FLOOR BOARD TO STOP THE CAR. NORMALLY, I BARELY TAP THE BRAKE PEDAL FOR IT TO STOP. THIS HAPPENED TWICE AND I TOOK IT TO A BRAKE SHOP. THEY REALIZED THIS BRAKE FAILURE HAPPENS BOTH GOING FORWARD AND REVERSE AFTER THE CAR SAT FOR OVERNIGHT. AFTER RESEARCH, THEY REALIZED THAT THIS IS A MAJOR BRAKE PROBLEM AND SUGGESTED I VISIT A FORD SERVICE CENTER SINCE THEY WERE NOT EQUIPPED FOR THIS TYPE OF REPAIR. I HAD THE FUSION TOWED TO MY LOCAL FORD DEALER. AFTER THE FIRST DIAGNOSTIC, THE DEALER SAID THAT IT IS THE HYDRAULIC CONTROL UNIT. I THEN MENTIONED TO THE DEALER EMPLOYEE THAT THERE ARE MANY REPORTS ON THIS VEHICLE HAVING THIS SAME SITUATION AND IT IS UNDER INVESTIGATION.

TL* THE CONTACT OWNS A 2012 FORD FUSION HYBRID. THE CONTACT STATED THAT THE ABS CONTROL MODULE FAILED AND CAUSED IRREGULAR BRAKING. THE CONTACT HAD TO DEPRESS THE BRAKE PEDAL WITH FORCE TO STOP THE VEHICLE. THE DEALER (STAR FORD LINCOLN, 1101 S BRAND BLVD, GLENDALE, CA 91204) STATED THAT THE ABS CONTROL MODULE NEEDED TO BE REPLACED. THE MANUFACTURER WAS NOT CONTACTED. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 80,000.

BRAKE PEDAL IS SOFT, AND TAKES LONGER TO STOP. HAD VEHICLE CHECKED - ALL BRAKE SYSTEMS FUNCTION CORRECTLY EXCEPT FOR ANTI-LOCK BRAKES-MODULATOR VALVE. SERVICE CENTER QUOTED $2282 TO REPLACE THE ASSEMBLY (# BE5Z2C215A). THE HIGH COST IS FOR 2010-2012 MODEL YEARS ONLY. THE COST DROPS SIGNIFICANTLY FOR THE 2014 FUSION. THE HIGH COST OF THIS SAFETY RELATED REPAIR, MAKES ESSENTIAL REPAIR UNAFFORDABLE. NHTSA OUGHT TO FORCE RELEASE OF AN AFFORDABLE PART, BASED ON SAFETY.

TL* THE CONTACT OWNS A 2012 FORD FUSION. THE CONTACT STATED THAT THE BRAKE PEDAL TRAVELED TO THE FLOORBOARD WHEN IT WAS DEPRESSED. THE CONTACT CAUTIOUSLY COASTED THE VEHICLE OVER TO THE SIDE OF THE ROAD AND PARKED IT AT HIS RESIDENCE DUE TO THE FAILURE. A DEALER WAS NOT CONTACTED. THE MANUFACTURER INDICATED THAT THE VEHICLE WAS OUT OF WARRANTY AND DID NOT ASSIST. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE VIN AND FAILURE MILEAGE WERE NOT AVAILABLE.

WHILE DRIVING DOWN MY STREET GOING ABOUT 10 MPH. MY BREAK PEDDEL WENT TO THE FLOOR WITH THE SOUND OF LOUD GROUNDING. I TOOK THE CAR BACK TO TBE HOUSE. IN THE PAST WEEK A BREAK BOOSTER NEW FRONT AND BACK PADS 1 CALIPER A MASTER CYLINDER AND ABS MODULE HAVE BEEN REPLACED. BREAKS ARE STILL NON EXISTANT.

AT THE APPROACH OF A STOP AT ABOUT 20 MPH OR LESS, WHEN DEPRESSING THE BRAKE PEDAL TO STOP THE BRAKE PEDAL GOES ALL THE WAY TO THE FLOOR FOR NO REASON AND CAR WILL NOT STOP AND AT TIMES PUTTING ME AND ANY PASSENGERS IN GREAT DANGER. THIS HAS HAPPENED MANY TIMES, MOST OFTEN WHEN PULLING OUT OF THE GARAGE BUT MOST RECENTLY HAS OCCURRED AT 3 DIFFERENT INTERSECTIONS AND 2 TIMES ALMOST T/BONED IN THE MIDDLE OF A BUSY INTERSECTION. AT WHAT POINT DOES IT TAKE FOR ME TO OR MY ONLY DAUGHTER TO DIE BECAUSE FORD WON'T STEP UP TO THE PLATE AND ADMIT THEY HAVE AN ISSUE WITH THE BREAKING SYSTEM ON THESE CARS? I HAVE HAD IT TO THE FORD SHOP AND I HAVE ALSO A CASE # RECORDED TO FORD. IT IS TIME FOR FORD TO TAKE ACTION AND RECALL THIS TYPE OF CAR BEFORE THERE IS AN UNNECESSARY DEATH RELATED TO THEIR NEGLIGENCE.

I HAVE HAD SEVERAL BRAKE FAILURES WHERE THE PEDAL WENT NEARLY TO THE FLOOR BEFORE THE BRAKES ENGAGED. THIS HAS ALWAYS OCCURRED AFTER A SUDDEN STOP, OR WHEN BRAKING IN A TURN. THIS TIME IT HAPPENED WHILE TRYING TO AVOID AND OBJECT THAT FLEW OFF THE BACK OF A TRUCK. AFTER PREVIOUS EVENTS I WAS ABLE TO BRING THE PEDAL BACK TO NORMAL BY PUMPING IT HARD A FEW TIMES, THIS TIME IT DIDN'T WORK. I DID SOME RESEARCH AND DISCOVERED THAT THIS WAS A COMMON, AND VERY DANGEROUS, OCCURRENCE. BEING AN ENGINEER, I DECIDED TO LOOK INTO IT FURTHER. WHAT I FOUND WAS THAT A COMPONENT IN THE ABS CONTROL, A DUMP VALVE, WAS FAILING TO CLOSE AFTER AN ABS EVENT. THIS IN ITSELF IS VERY DANGEROUS, BUT THE FACT THAT THE SYSTEM DOESN'T SEND OR RECORD AN ERROR IS INEXCUSABLE. MY RESEARCH HAS LED ME TO CONCLUDE THAT THIS IS A DESIGN FLAW IN THE CONTROL UNIT. THE FACT THAT IT DOESN'T POP AN ERROR IS VERY SUSPICIOUS. FORD HAS KNOWN ABOUT THIS FLAW FOR A LONG TIME, AND IT AFFECTS ALL MODEL YEARS FROM 2005-2012. I ALSO FOUND OUT THAT THE PROBLEM WAS BEING INVESTIGATE (BY YOU I ASSUME), BUT ONLY INCLUDES MODEL YEARS FROM 2005-2010. IT DOES IN FACT INVOLVE ALL OF THE FIRST GENERATION FUSIONS. IN INVESTIGATING FURTHER, I DISCOVERED THAT FORD ENGINEERS NOT ONLY KNEW ABOUT THE PROBLEM. THEY DISCOVERED WHAT WAS CAUSING IT. IT SEEMS THERE IS AN INCOMPATIBILITY OF SOME OF THE INTERNAL (WETTED) COMPONENTS AND THE BRAKE FLUID. A CHEMICAL REACTION OCCURS, OVER TIME, CAUSING THE DEVELOPMENT OF A GEL LIKE MATERIAL THAT CAUSES THE VALVES TO STICK IN THE OPEN POSITION. PEOPLE HAVE BEEN INJURED BECAUSE OF FORDS FAILURE TO ACT, AND THERE WILL BE MORE IN THE FUTURE, THERE ARE A LOT OF THESE CARS STILL ON THE ROAD. FORD SHOULD FIX THE PROBLEM, AND RECALL ALL AFFECTED VEHICLES STILL IN SERVICE.

I'VE HAD MY BRAKES SERVICED MULTIPLE TIMES, BUT MY BRAKE PEDAL KEEPS FAILING AND GOING ALL THE WAY DOWN TO THE FLOOR.

CLIENT APPROACHED AN INTERSECTION WITH A LEFT TURN, APPLIED THE BRAKES. THEY WENT TO THE FLOOR, VEHICLE NEVER STOPPED OR SLOWED DOWN UNTIL RUNNING THROUGH A SIGN, INTO AN EMBANKMENT. CLIENT WAS SEVERELY INJURED AS A RESULT. VEHICLE WAS A TOTAL LOSS. VEHICLE IS CURRENTLY STORED AT A TOW YARD. WE HAVE 30 DAYS TO GET THE VEHICLE INSPECTED BY THE NHTSA. PLEASE CONTACT MY OFFICE TO GET THE ADDRESS.

TL* THE CONTACT OWNED A 2012 FORD FUSION. WHILE DRIVING AT AN UNKNOWN SPEED, THE VEHICLE FAILED TO STOP WHEN THE BRAKE PEDAL WAS DEPRESSED. THE CONTACT'S DAUGHTER STATED THAT THE BRAKE PEDAL FELT SOFT. AS A RESULT OF THE FAILURE, THE CONTACT'S DAUGHTER REAR ENDED ANOTHER VEHICLE. THERE WERE NO INJURIES AND A POLICE REPORT WAS FILED. THE VEHICLE WAS TOWED FROM THE SCENE TO A SALVAGE YARD WHERE IT WAS DEEMED DESTROYED. THE DEALER AND MANUFACTURER WERE NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 85,000.

TL* THE CONTACT OWNS A 2012 FORD FUSION. WHILE ACCELERATING FROM A TRAFFIC LIGHT, THERE WAS A GRINDING NOISE COMING FROM THE REAR BRAKES. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC TO BE DIAGNOSED. THE CONTACT WAS INFORMED THAT THE ROTORS AND BRAKE PADS NEEDED TO BE REPLACED. THE CONTACT WAS INFORMED THAT THERE WAS METAL-TO-METAL CONTACT BETWEEN THE BRAKE PADS AND THE ROTORS. THE CONTACT WAS CONCERNED THAT THE BRAKE WARNING SENSOR FAILED TO NOTIFY THAT THE BRAKES NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED. A DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 40,000. THE VIN WAS NOT AVAILABLE.

TL* THE CONTACT OWNS A 2012 FORD FUSION. WHILE DRIVING APPROXIMATELY 45 MPH, THE BRAKE PEDAL WAS DEPRESSED AND TRAVELED TO THE FLOORBOARD. THERE WERE NO WARNING INDICATORS ILLUMINATED. A LOCAL DEALER WAS NOT CONTACTED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE BRAKE PADS NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED; HOWEVER, THE FAILURE RECURRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE AND VIN WERE UNKNOWN.

2012 FORD FUSION PURCHASED FROM AUTOFAIR FORD 08/11 2.5LTR , 6 SPEED MANUAL, 62K MILES ORIGINAL OWNER. ON 02/09/2017 ABOUT 2 PM UPON APPROACHING A RURAL STOP SIGN EXPERIENCED AN ABS BRAKE ACTION DUE TO VERY SLIPPERY SNOW CONDITIONS. I STOPPED VERY SLOWLY AND WAS SURPRISED THE ABS ACTIVATED, IN FACT I DON'T THINK I HAVE EVER HAD THEM ACTIVATE LIKE THIS. 5 VERY LOUD BANGING SOUNDS AS SOMEONE WAS HITTING THE FRONT UNDERSIDE OF CAR WITH A LARGE HAMMER. I IMMEDIATELY LET OFF THE BRAKES AND SLOWLY RE-APPLIED TO FIND I HAD NO BRAKES AT ALL. BRAKE PEDAL SANK TO FLOOR AND I WENT THROUGH INTERSECTION OUT INTO CONNECTING ROAD. I USED THE E-BRAKE TO STOP AND LUCKILY NO ON COMING CARS. DROVE CAR HOME VIA E-BRAKE AS HAD NO BRAKES. WHEN HOME CHECKED FLUID THEN DID SOME RESEARCH ON LINE AND FOUND OTHER PEOPLE ARE EXPERIENCING THIS. READ ON LINE TO DISCONNECT THE ABS FUSE AND BRAKES MAY WORK AGAIN WHICH THEY DID BUT AS ABS FUSE IS OUT AND I HAVE BRAKES, I DO NOT HAVE ABS OR TRACTION CONTROL. I HAVE READ THAT I CAN PUT THE ABS FUSE BACK IN BUT IF I EXPERIENCE ANOTHER ABS DEPLOYMENT, THE SAME RESULT OF LOSS OF BRAKE PEDAL WILL HAPPEN, NOT A SAFE RIDE I WOULD SAY. I HAVE HAD AN ON-GOING TYPE OF SITUATION HAPPENING WHEN MAKING HARD RIGHT TURNS IN TO TRAFFIC AND HAVING TO ACCELERATE FAST. ( THE CAR APPEARS TO BE SOMEHOW FOOLED AND THE TRACTION CONTROL OVER REACTS AND CAR STARTS BUCKING HARD AND ALMOST STALLS OUT. I HAVE TO PUSH IN CLUTCH TO STOP IT AND AVOID STALLING AND GETTING HIT. NOT SAFE. I HAD ACTUALLY GOT IN THE HABIT OF SHUTTING OFF TRACTION CONTROL IN THESE TYPE OF TURNS PRIOR TO THE EVENT ORIGINALLY STATED HERE. I HAVE READ THAT THERE IS SOME TYPE OF ABS VALVE BODY COMING INTO SUSPECT AS THE ISSUE AND NO RECALLS HAVE BEEN ORDERED AND ITS ALSO AN EXPENSIVE FIX. WHICH AS BEING SAFETY RELATED DEFECT I FEEL IT SHOULD BE LOOKED INTO.

TL* THE CONTACT OWNS A 2012 FORD FUSION. THE CONTACT STATED EXCESSIVE PRESSURE WAS NEEDED WHEN DEPRESSING THE BRAKE PEDAL IN ORDER FOR THE VEHICLE TO BE ABLE TO STOP SAFELY AT ANY SPEED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 48,000.

ON COLD STARTS THIS SUMMER I BACK OUT OF MY DRIVEWAY AND PRESS THE BRAKES TO STOP AND THE BRAKE PEDAL IS ROCK HARD AND I CAN'T STOP. THIS IS GOING TO BE MY THIRD TIME FOR THIS PROBLEM. THE DEALERSHIP HAS REPLACED THE BRAKE BOOSTER, MASTER CYLINDER, BRAKE FLUID RESERVOIR AND BRAKE BOOSTER CHECK VALVE AND VACUUM HOSE.

I WENT IN FOR A ROUTINE OIL CHANGE AND CAR CHECK UP. THEY TOLD ME THERE IS BRAKE FLUID LEAKING FROM THE MASTER CYLINDER INTO THE BRAKE BOOSTER AND IT RUSTED. BACK BRAKES AND ROTORS NEEDED, FLUSHING SYSTEM $1400? THEY SAID I WAS LUCKY CAUSE THEY COULD GIVE OUT AT ANYTIME CAUSING A FATAL ACCIDENT.

TL* THE CONTACT OWNS A 2012 FORD FUSION. THE CONTACT THAT WHILE REVERSING AND DEPRESSING THE BRAKE PEDAL, THE BRAKES FAILED TO RESPOND. THE CONTACT MENTIONED THAT THE VEHICLE WAS AT AN INCLINE AND SHE CONTINUED TO DEPRESS THE BRAKE PEDAL BUT IT TRAVELED TO THE FLOORBOARD. AS A RESULT, THE CONTACT TURNED VIOLENTLY TO THE RIGHT IN ORDER TO AVOID CRASHING INTO THE NEIGHBORS HOUSE AND CRASHED INTO A FENCE ON THE DRIVERS SIDE. THE VEHICLE WAS TOWED TO THE DEALER BUT THE FAILURE WAS UNDETERMINED. THE APPROXIMATE FAILURE MILEAGE WAS 39,000.

TL* THE CONTACT OWNS A 2012 FORD FUSION. THE CONTACT STATED THAT THE BRAKE SYSTEM FAILED TO ENGAGE. ON ONE OCCASION, THE CONTACT REVERSED FROM THE DRIVE WAY AND THE BRAKE PEDAL STUCK TO THE FLOOR BOARD CAUSING THE CONTACT TO CRASH INTO A FENCE. THE VEHICLE WAS TOWED TO THE LOCAL DEALER FOR FURTHER INSPECTION. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 39,000.

TL* THE CONTACT OWNS A 2012 FORD FUSION. WHILE SHIFTING THE GEAR SHIFTER INTO DRIVE, THE CONTACT ATTEMPTED TO DEPRESS THE BRAKE PEDAL. THE PEDAL FAILED TO DEPRESS AND THE CONTACT HEARD AN ABNORMAL NOISE COMING FROM THE PEDAL. THE VEHICLE WAS TAKEN TO A DEALER WHERE IT WAS DIAGNOSED THAT THE HYDRAULIC CONTROL UNIT NEEDED TO BE REPLACED AND REPROGRAMMED. THE VEHICLE WAS REPAIRED; HOWEVER, THE FAILURE RECURRED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHO DIAGNOSED THAT THE HYDRAULIC CONTROL UNIT NEEDED TO BE REPROGRAMMED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 120,000.

TL* THE CONTACT OWNS A 2012 FORD FUSION HYBRID. THE VEHICLE WAS REPAIRED UNDER FORD'S CUSTOMER SATISFACTION THAT WAS RELATED TO NHTSA ACTION NUMBER: PE14030 (STEERING). THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 55 MPH, THE BRAKE SYSTEM WARNING, ADVANCED TAC, AND ABS WARNING INDICATORS ILLUMINATED. THE VEHICLE WAS DRIVEN TO THE CONTACT'S RESIDENCE. THE CONTACT POWERED THE VEHICLE OFF AND BACK ON; HOWEVER, WHEN THE VEHICLE WAS PLACED IN REVERSE, THE CONTACT DEPRESSED THE BRAKE PEDAL AND THE PEDAL WENT TO THE FLOORBOARD AND FAILED TO STOP THE VEHICLE. THE VEHICLE CONTINUED IN REVERSE INTO ONCOMING TRAFFIC AND NEARLY CAUSED A CRASH. THE CONTACT POWERED THE VEHICLE OFF AND BACK ON AND THE BRAKE PEDAL RETURNED TO NORMAL. THE CONTACT DROVE THE VEHICLE TO AN INDEPENDENT MECHANIC, HOWEVER, THE MECHANIC WAS UNABLE TO DIAGNOSE THE FAILURE. THE VEHICLE WAS TOWED TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE BRAKE DRUM WAS FAULTY AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 73,800.

2012 FORD FUSION. CONSUMER WRITES IN REGARDS TO BRAKE SYSTEM PROBLEMS. *SMD THE CONSUMER STATED SHE COMPLAINED TO THE DEALER ABOUT A CLICKING SOUND. AFTER SHE STARTED THE VEHICLE, PUT IT IN GEAR, WITH HER FOOT ON THE BRAKE, THE SOUND COULD BE HEARD. AT THAT TIME, IT WAS SPORADIC. EACH TIME SHE VISITED THE DEALER, THEY WERE UNABLE TO FIND ANYTHING WRONG. *JB

TL* THE CONTACT OWNS A 2012 FORD FUSION. THE CONTACT TOOK THE VEHICLE IN TO THE DEALER FOR A CHECK-UP AND IT WAS FOUND THAT THE REAR PASSENGER SIDE OF THE BRAKE PADS WERE METAL ON METAL. THE BRAKE PADS WERE REPLACED; HOWEVER, 5,000 MILES LATER, THE BRAKES STARTED TO MAKE A GRINDING SOUND AGAIN. THE VEHICLE WAS TAKEN BACK TO THE DEALER AND IT WAS DETERMINED THAT THE BRAKES NEEDED TO BE REPLACED AGAIN. THE DEALER STATED THAT THE FAILURE OCCURRED BECAUSE OF THE SNOW, BUT THE CONTACT STATED THE SAME FAILURE OCCURRED WHILE IN FLORIDA WITH NICE WEATHER. THE CONTACT SPOKE TO THE MANUFACTURER AND WAS INFORMED THAT THIS WAS NORMAL WEAR FOR THE BRAKE PADS. THE CONTACT STATED THAT THE MANUFACTURER REFUSED TO REPAIR THE VEHICLE. EACH BRAKE CHANGE LASTED LESS THEN 14,000 MILES. THE FAILURE MILEAGE WAS 55,233.

TEMPERATURE WAS -3 DEG F. STARTED CAR FROM BEING COLD OVERNIGHT. LET ENGINE RUN NO MORE THAN 3 MINUTES PRIOR TO BACKING OUT OF DRIVE WAY. MADE TWO SUCCESSFUL STOPS. DROVE 3/8 MILE FROM LAST STOP WHILE TRAVELING AT 30 MPH. SLOWED TO MAKE RIGHT TURN ON DESIRED STREET BECAUSE TRAFFIC LIGHT WAS GREEN. WHILE TURNING BRAKE WARNING LIGHT ILLUMINATED. ABS FAILURE AND TRACTION CONTROL FAILURE LIGHTS ILLUMINATED. VEHICLE WAS VERY HARD TO STOP WITH FOOT BRAKE. LOSS OF ALL POWER ASSISTANCE FOR STOPPING. DEALER RECORDED ABS SYSTEM TEST, C0022, ABS PINPOINT TEST P, CIRCUIT TEST, EXCESSIVE RESISTANCE BETWEEN PINS 17 AND 31. AT ABS MODULE CONNECTOR C135, 3.3 OHMS, TRACE, REMOVED AND INSTALLED PCM AND MASTER CYLINDER TO ACCESS AND REPAIR WIRE CIRCUITS CCA22 GREY WITH YELLOW AND VCA22 GREEN WITH BROWN, GREEN CORROSION AT CONNECTOR C1602 PINS 3 AND 4 NEAR THE BRAKE BOOSTER SOLENOID CONNECTOR. *TR

WHEN LEAVING MY DRIVEWAY THE BRAKES FAILED TO FUNCTION PROPERLY AND I ALMOST ROLLED INTO A CAR ON THE STREET. I CAME TO UNDERSTAND THAT THE POWER ASSIST FAILED. BUT THE EXPERIENCE WAS THAT THEY DIDN'T WORK UNTIL THE BRAKE PEDAL WAS NEARLY TO THE FLOOR, AND VERY SOFT. I DROVE SLOWLY FORWARD AND THEY CONTINUED TO NOT WORK. I TURNED OFF THE CAR AND HAD IT TOWED TO A DEALER FOR SERVICE. APPARENTLY WHEN THE SERVICE PEOPLE TURNED ON THE CAR THE BRAKES WORKED AND THEY COULDN'T GET THE PROBLEM TO REPEAT, BUT THE COMPUTER ON THE CAR LOGGED A BRAKE INCIDENT. FORD WOULDN'T DO ANYTHING FOR ME AND TOLD ME TO KEEP DRIVING THE CAR UNTIL IT HAPPENED AGAIN. THEY SAID IF THEY FIXED SOMETHING THEY WOULD GIVE ME A "FALSE SENSE OF SECURITY". IN SEARCHING ONLINE I FOUND THIS IDENTICAL PROBLEM HAD BEEN PART OF A RECALL ON EARLIER MODELS (2010) THAT WAS A SOFTWARE GLITCH. *TR

I BROUGHT MY CAR IN TO THE DEALERS FOR A WARRANTY ISSUE. UPON CHECKING THE VEHICLE, THEY INFORMED ME THE REAR BRAKE PADS WERE WORN TO THE METAL AND WERE DAMAGING THE ROTORS. THEY SUGGESTED IT WAS UNSAFE AS IS AND I SHOULD HAVE THE REAR PADS AND ROTORS REPLACED ASAP. I DRIVE LONG DISTANCES EACH DAY AND USUALLY GET 70-80,000 MILES BEFORE NEEDING THE FRONT PADS REPLACED AND OVER 100,000 MILES BEFORE NEEDING NEW ROTORS REPLACED. I FEEL THERE IS A MAJOR PROBLEM/MALFUNCTION WITH THE REAR BRAKES ON FORD FUSIONS AND THEY SHOULD BE INVESTIGATED AND A SAFETY RECALL ISSUED. *TR

TRAVELING ON CROWDED HIGHWAY WHEN CARS AHEAD STOPPED; MY BRAKES WHEN THUMP THUMP THUMP THEN I REAR-ENDED THE CAR IN FRONT OF ME. CAR DID NOT SLOW DOWN AT ALL. FORTUNATELY NO ONE WAS KILLED OR SERIOUSLY INJURED, BUT MY INSURANCE WILL DEFINITELY GO UP. TAKING THE CAR TO THE DEALER ON MONDAY MORNING. *TR

TL* THE CONTACT OWNS A 2012 FORD FUSION. THE CONTACT STATED THAT WHENEVER IT RAINED AND THE VEHICLE SAT OVERNIGHT, THE NEXT MORNING THE BRAKES WOULD GRIND FOR A MILE OR WOULD SEIZE. THE CONTACT STATED THAT AFTER GOING A MILE, THE BRAKES FUNCTIONED PROPERLY. THE VEHICLE WAS TAKEN TO THE DEALER FOR INSPECTION AND THEY STATED THAT IT WAS NORMAL AND THEY WOULD REPLACE THEM. THE VEHICLE WAS REPAIRED BUT THE FAILURE RECURRED. THE MANUFACTURER WAS NOTIFIED BUT PROVIDED NO ASSISTANCE. THE FAILURE MILEAGE WAS 13,000....UPDATED 04/25/13 *BF UPDATED 05/17.2013 *JS